电压空间矢量脉宽调制的简单算法

在电压空间矢量脉宽调制(SVPWM)控制技术原理的基础上,提出了一种简单快速算法,该算法只有普通的四则运算,计算变得非常简单,消除了常规的空间矢量控制算法中由于三角函数和无理数的近似计算而带来的计算误差及影响计算精度和速度的缺点,使结果更加准确。因而更适合应用于基于DSP 的数字化控制。理论分析和大量的MATLAB仿真结果表明,该算法具有谐波含量低、直流电压利用率高的优点。     

基于HYDRUS-2D的地下滴灌下水分运移数值模拟研究

利用HYDRUS-2D软件模拟了地下滴灌条件下滴头周围黏壤土的土壤水分动态,并与田间观测进行对比;通过分析不同滴头流量对试验地土壤湿润模式的影响,明确了最佳灌水技术参数。结果表明,HYDRUS-2D软件模拟结果与观测值一致,体积含水率均方根误差为1.2%~4.5%,湿润范围均方根误差变化范围为2.1~3.87cm。     

低雷诺数工况下锯齿型翅片性能的参数化研究

基于田口方法,结合均匀设计法对低雷诺数工况下错列锯齿型翅片进行三维参数化数值研究。以单层翅片组件为测试对象,对6种试件的试验表明,仿真结果与试验数据的趋势吻合良好,而存在差异的主要原因是试件加工工艺引起翅片表面存在毛刺。按照均匀设计法得到6因子5水平的11种仿真方案,引入田口方法的信噪比和贡献率,研究各几何参数对翅片性能的影响程度,依次为齿距、齿高、齿型角、错齿距、齿开窗宽度和齿厚。根据各水平下各可控因子的信噪比分布得到翅片的优化模型,并通过仿真验证了优化模型的有效性。     

群井开采条件下承压含水层渗流动态模拟

根据有限差分方法 ,编制了承压含水层渗流模拟软件。对某水源地在群井开采情况下地下水渗流动态进行数值模拟。模拟结果显示 ,位于高渗区的井 ,压降漏斗较其它井大 ,压力下降快。当地层中存在裂隙时 ,平行裂隙方向压力下降比垂直裂隙方向要快得多。抽水初期 ,地层压力下降很快 ,以后 ,压力下降逐渐变缓 ,位于低渗透区的井逐渐不能满足流量要求。因此做好地下水资源规划十分重要     

FLUENT软件及其在植保机械方面的应用

FLUENT软件是流体力学中通用性较强的商业软件之一，由于FLUENT软件的应用，节省了大量的人力和物力。对实际应用有重大的指导作用。为此，通过简述FLUENT在植保机械方面的应用实例，提出了FLUENT在植保机械方面的发展前景。     

砌石拱坝加高倍厚的三维接触仿真

对砌石拱坝的加高倍厚中新、老坝体结构面，用有限元软件ANSYS结合接触理论进行计算，并分析结果得出：温升、水压力和淤沙压力使结合面上的接触压力增大，从而接触摩擦应力较大，有利于结合面的结合，而结合面在温降的作用下有脱离的趋势。     

Simulation on the Characteristics of Flow Pattern in Sprial uP-flow Reactor

In order to analyze the reason why the Spiral Up-flow Reactor system has excellent removal effect of COD, N and P, the authors use PHOENICS, a computational fluid dynamics program, to investigate the hydraulic characteristics and flow model of the anaerobic part of Spiral uP-flow reactor. The result shows that the fluid in the reactor unit flowed upward by the spiral way, and that flow pattern was combined by plug flow and complete-mix flow, and that the percentage of plug flow was about sixty-five percent. Spiral Up-flow Reactor units the Characteristics of PFR and CSTR, which makes it work well.     

Analysis and FEM Simulation of the Forming Process of Front Bumper Bracket

The processing characteristics of the front bumper bracket are analyzed,and a reasonable process scheme is worked out.The three-dimensional sheet metal forming analysis software PAM-STAMP are adopted to simulate the bracket's drawing process.Then the surface of die is proved fine through analyzing the FLD diagrams and the forming results.An economical and optimized die structure is decided,and a complete set of dies of the bracket is designed.The spacing block is added in the sizing mold,which control the size precision of end products and assembling columns actively,and finally the certified products.The material utility and the labor productivity are raised,the production cost is saved,and the mold design quality and the efficiency are improved effectively.     

Two Types Modules for the Boiler Attached to 330 MW Unit

Boiler is an important facility in power plant , the safety and economy of unit is affected by it. Studying the dynamic of boiler can improve the knowledge about boiler , which is important for. Features of MMS are introduced based on MMS simulation setting, and the real time capable module and non real time capable module are compared from principle. Real time capable dynamic model of boiler and non real time capable dynamic model of boiler of 330 MW unit are established . The experimental results show that the dynamic process of two type model accords with the mechanism of the object , at the same time, the validity of real time capable module is discussed .     

Simulation for Logistics in Steel-making Process of Panzhihua Iron and Steel Corporation

To solve potential scheduling problems in production after renewal of continuous casting process in Vanadium-extracting and Steel-making Plant of Panzhihua Iron and Steel Corporation (PISCO), how to model and simulate logistics system in steel-making processhas been discussed. A series of simulatingtests for logistics system in steel-making processhave been conducted based on inputs of presentsteel-making processof PISCO. In the tests, cases of regular schedule case and cases with repairing converter have also been regarded as essential simulation condition. It has been shown that three casters can not start at same time in order to ensure continuous hot metal supply for casters when three kinds of steel are made. It has also been shown that the simulation system for logistics system in steel-making processis valid and can be used for simulating logisticsin upcoming 100% continuous casting process of PISCO. The better schedule scheme of production and reasonable match of converter-caster in time and capacity can be achieved with the help of using simulation approach.